SmartgridOne logo
SmartgridOne logo
Accessories
AppCertificates
Configuration from A to Z
Control response timeController
Customer Specific
Devices
Boiler
Cloud
Energy Meter
Ev Charging Station
Gas Meter
Heat Pump
New integrations
Plc
Pv Hybrid And Battery Inverters
a-TroniXABB, FIMERADS-TecAforeAlphaESSAlpvoltAmpowrAngileAnklous PV, Hybrid and Battery InvertersAPsystemsAteps Battery
Autarco
BattlinkBeauventC-BatteryCellpowerChisageDanfossDeltaDET Power PV, Hybrid and Battery InvertersDEYEDiehl-AkoDMEGC InvertersDynessDysun EnergyEcosourcenEenovanceElecnovaEnbrilionEnergreenEnerlutionEnjoyPowersEnphaseEP EquipmentESY InvertersEVEFairlandFortona
Foxess
FraxFroniusGoodWeGotionGreener / Alfen
Growatt
HiteHithium
Huawei
Hypontech
Hyxipower
iWellJinkoKacoKehuaKostal
Kstar
LibattionMarstekMastervoltMidTeQMotomaOctave EnergyOmniPowerPixiiPower-SonicPoweroadPylontechRCT PowerRefurbRegitecRenonRitarSAJSavSchneider SunEzySchucoSCUSessySigenergySinexcel
Sma
Socomec
Sofar
Solaredge
SolarlogSolarMaxSolarwattSolaxSolinteg
Solis
Solplanet
Sungrow
SunsynkSunwaytechSunwoda
Sunwoda
Sus-PowerTeclomanTeploreTesvoltVaconVictronVolstoraWattsNextWeiheng
WHES
Hybrid Inverter 3.6-6kWHybrid Inverter 5-13kWPC-G1 100kW/233kWhPC-G2 250kW/509kWhPC-mini 29.9-50kW 57-100kWhPP-S1 3.6-6kW/5.12-10.24kWhPP-S2 3.6-10kW/4.99kWh-99.9kWhPP-T1 5-13kW/9.98-29.94kWh
XantrexZendure SolarFlowZetaraZeversolar
Switched Loads
Water Meter
External Signals
InstallationLicenseNetworkQuick StartSafety, maintenance and legal noticesSpecificationsStatus LEDs
Toolbox
Troubleshooting
Video tutorialsWiring & connectivity guidelines
DevicesPv Hybrid And Battery InvertersWHES
WHES

PP-S2 3.6-10kW/4.99kWh-99.9kWh

Supported Devices

Device TypeModbus TCP (Ethernet)RS485Curtailment
SIA-3.6kW✅❌⚠️
SIA-5kW
SIA-6kW
SIA-8kW
SIA-10kW
  • Protocol driver: WHES Single Phase Hybrid Inverter Protocol (RTU)
  • Default TCP port: 502

Configuration

Ethernet Connection

Make sure the Controller and the SmartgridOne are connected to the same network.

  • Connect the SmartgridOne Ethernet port to the same switch/router as the Controller.
  • Ensure the SmartgridOne has a reachable IP address.
  • TCP port must be 502 .

For correct ethernet wiring: Follow the the guidelines for ethernet wiring.

Device settings

⚠️ Make sure the device Direct power control read-only mode is off. If it is on we can't send commands with the SmartgridOne.

Last updated June 23, 2026Edit this page

PP-S1 3.6-6kW/5.12-10.24kWh

Previous Page

PP-T1 5-13kW/9.98-29.94kWh

Next Page

On this page

PP-S2 3.6-10kW/4.99kWh-99.9kWhSupported DevicesConfigurationEthernet ConnectionDevice settings